Green Chicken Wire

Step 1 – Mark Area

Draw a straight line for the fence between the two posts located at each end.

Step 2 – Measure Post Distance

Employ a tape measure to mark the positions of the posts, ensuring they are spaced 2 to 3 meters apart.

To improve stability, reduce the distance between your fence posts.

Step 3 – Install End Posts

Use a post driver or mallet to embed the end posts 50cm into the ground.

Ensure that the holes of the posts are oriented towards each other to maintain consistent alignment.

Step 4 – Check for Same Height

Secure a length of string between the end posts, then verify that they are installed at the same height by employing a tape measure.

Step 5 – Check for Straightness

Use a spirit level to confirm that the posts have been installed completely straight.

Step 6 – Set in Concrete (Optional)

For a stronger and more secure fence, place your posts in concrete by excavating a 50cm hole and pouring cement for the post to settle in.

Step 7 – Install Middle Posts

To set up middle posts, repeat steps 3 through 5.

Make sure that the posts are oriented in the same direction and are installed both straight and at equal heights.

You may also reinforce the middle posts with concrete for additional strength.

Step 8 – Install Tension Wire (Optional)

When working with lightweight mesh, consider attaching a tension wire between the end posts to prevent any potential sagging.

Wrap the tension wire around the hole of the end posts and secure it by twisting the end of the wire with pliers.

Step 9 – Attach Mesh to End Post

Fasten the mesh to the end post using cable ties, threading them through the pre-drilled holes in the post.

You can further reinforce the attachment by adding additional cable ties around the entire post.

Step 10 – Pull Tight

Pull the mesh taut and then fasten it to the second post using cable ties, being careful not to pull too tightly.

Repeat this procedure until you reach the end post.

Step 11 – Attach to Tension Wire (Optional)

If you’ve installed a tension wire, use cable ties to secure the mesh to it, spacing them roughly 30-45 cm apart.

Step 1 – Mark the Post Location

Indicate the post locations with a spacing of 2-2.5 meters between each one.

Step 2 – Dig Holes

Excavate a hole to accommodate your post. The depth of the hole should be approximately one-third of the post’s height.

Use a spirit level to confirm that the posts are perfectly straight.

Step 3 – Cement Posts In (Optional)

Fill the holes with concrete, then position your posts into the concrete.

Utilize a spirit level to confirm that the posts are straight.

Step 4 – Dig a Trench

Excavate a trench along your fence line for the netting, ensuring it is 30cm deep.

Step 5 – Install Tensioning Wire (Optional)

To ensure a sturdy and secure fence, employ tensioning wire in several rows, with at least one row at the top and one at the bottom.

Additional rows can be added according to your preference.

Instructions for tensioning a fence can be found here.

Step 6 – Attach Mesh to End Post

Retrieve sufficient netting to cover the span between the first two posts.

Fasten the mesh using staples or cable ties at intervals of every 15cm, leaving an additional 15cm at the bottom, facing outward.

Step 7 – Bend the Mesh

Fold the bottom of the mesh at a 90-degree angle, forming a 15cm lip.

This flap will conceal the bottom of the trench on the outside of your fence.

Step 8 – Attach Mesh to Posts

Secure the remaining portion of the mesh by following steps 6 and 7 repeatedly.

Step 9 – Attach to Tension Wire (Optional)

If you utilized tensioning wire, fasten it to the fencing at various points to assist in maintaining the fence tautness.

Step 10 – Secure the Flap

Secure the flap to the ground using pegs.

Staple at the 90-degree angle and also at the outer edge of the lip. Repeat this process every 60cm.

Step 11 – Cover the Trench

Apply 5cm of soil or mulch to conceal the outer flap.

Optional: Incorporate a layer of concrete into the trench to bolster security against digging.